







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Fence Installation: The Mission Viejo Owner’s Guide
Tamko fence installation in Mission Viejo typically runs $3,500 to $9,000 installed, depending on linear footage, gate count, and how much old fence and footing has to come out first. We handle the removal, post setting, panel and gate hang, and final cleanup as one written scope. Most jobs are scheduled, not same-day, because a fence that holds in Mission Viejo’s clay soils needs proper footing depth and cure time before panels go up.
Owners usually find this page the same way: a gate that sags and drags by midsummer, a post that’s gone soft where it meets the dirt, or a run of pickets that leans after a Santa Ana wind event. The material itself often looks fine from the street. What’s failed is underneath – the footings, the fasteners, or the coating on the post that was never rated for the sun load on a south-facing slope.
Which Tamko Models This Applies To

Tamko’s fence and railing offerings split into distinct product lines, and the parts don’t cross over. Before anything gets ordered, we confirm which line you actually have by checking three things: the label inside the post cap or on the rail end, the actual face width of the picket (nominal sizes vary by line and get misremembered as the same), and the post dimensions measured at the base, not at the top where the cap can distort the read. A tape measure and the original spec sheet, if you kept it, save a return trip.
On OEM versus aftermarket: for Tamko-branded brackets, caps, and gate hardware, we match OEM where the part carries the load or the coating warranty. For pickets and rails, quality aftermarket extrusions in the same profile can work, but only when the wall thickness and color lot match what’s already standing. A rail that’s a sixteenth off in profile will fight every bracket on the run. We’re an independent service provider and not affiliated with Tamko, so we order to your model, not to a house brand. We also install KraftMaid, Cambria, and Silestone products on the interior side when a project runs inside and out.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Tamko Fence Installation Is Failing
- Posts that move when you push on them. Soft footing or a post that was set in soil instead of concrete. In Mission Viejo, the shrink-swell clay on many lots lets a post rock seasonally until the panel joints open.
- Rust weeping from the fasteners or post base. Coated fasteners that were never rated for coastal-influenced humidity. Once the coating fails, the fastener corrodes faster than the surrounding post.
- Gates that sag and drag within a season. A hinge side that’s moved, or a gate built too wide for its post. A gate over 5 feet wide needs a stiffer frame or a second hinge point, and many picket gates aren’t built that way.
- Chalking, fading, or chalky white residue on the finish. Sun exposure on a south or west run. UV load in Mission Viejo is high enough that a finish not rated for full sun breaks down years before the structural material does.
- Leaning runs after a wind event. Undersized footings. Wind catches a fence like a sail, and a footing set too shallow will tip before the panel fails.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed pricing for a Tamko fence in Mission Viejo lands in the $3,500 to $9,000 range. A straightforward privacy run on level ground sits near the bottom; long runs, slopes, gate work, and old-fence demolition push toward the top. Here’s what drives the number and what’s inside it:
| Line item | Typical range |
|---|---|
| Material (pickets, rails, posts, caps) | $1,200 – $3,800 |
| Demo and haul-away of old fence | $300 – $900 |
| Post setting and footings | $800 – $2,000 |
| Gate build and hang | $400 – $1,200 |
| Labor and installation | $800 – $2,100 |
Parts and labor are itemized separately on the quote so you can see exactly what a higher spec costs you. You get a written price before any work starts – no number that moves at the door. Every completed fence carries the 365-Day Done Right Promise: if the work fails inside a full year, we come back and correct it at no charge.
DIY or Call Us?
Some things are worth checking yourself. Walk the run and press on each post. Look for rust staining at the fasteners. Measure your gate width and check the picket face width for the parts match. Photograph the label on the post cap. That’s a ten-minute inspection and it tells you whether you’re looking at a hardware swap or a footing problem.
Where DIY goes wrong on fences is the footing and the gate geometry. A post set too shallow, or a gate frame that’s undersized for its span, will fail again within a season no matter how neatly the panels go up. Wind loads on a long run are not something you want to learn by trial. Our technicians have up to 22 years of experience, are background-checked and uniformed, and you’ll know who’s coming before they arrive. Call (833) 734-2429 for an honest read on whether your fence needs repair or replacement.
FAQs

A properly installed Tamko fence run typically lasts 15 to 20 years in this climate, with the footings and fasteners usually failing before the fence material itself. Sun exposure on south and west runs shortens finish life, and the clay soils common on Mission Viejo lots put more stress on posts than coastal sand does. Call (833) 734-2429 for a free estimate on your specific run.
Often yes, if the failure is isolated to a gate, a few pickets, or one post. A single soft post can be reset or replaced without touching the rest of the run, and gate hardware is a straightforward swap. If three or more posts are moving, replacement usually costs less over five years than repeated repair. Call (833) 734-2429 and we’ll tell you which side of that line you’re on – estimates are free.
A standard residential fence replacement in Mission Viejo runs two to four days for most lots, with demo, footings, and cure time built into the schedule. Larger runs, slopes, and multiple gates push toward the longer end. We give you the schedule in writing before work starts, and weather can shift it – we’ll call you, not leave you guessing. Call (833) 734-2429 to get your timeline priced.
We order to your confirmed Tamko line and model, not to a guess, using the label and measurements from your existing run. OEM hardware goes in where it carries load or warranty; quality aftermarket material is an option only when profile and color lot match. Parts are ordered and staged before the crew arrives, so the job doesn’t stall mid-run. Call (833) 734-2429 to start with a free estimate.
Whether your Tamko fence needs one post reset or a full run replaced, you get the same thing from us: a written price before any work starts, a documented scope, and a clean site at close with your signed 365-Day Done Right Promise in hand. A live person answers the phone any hour – call (833) 734-2429 to schedule your free estimate.
Written by the team at Bradford Remodeling Co Mission Viejo, serving Mission Viejo and nearby areas.












