







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Mission Viejo Owner’s Guide
We build Schluter-compatible home additions and ADUs in Mission Viejo, and the installed cost runs $45,000 – $130,000 for a home addition and $90,000 – $220,000 for a full ADU. If your project involves a failing Schluter tile or waterproofing assembly, it usually shows up as loose tile, grout that won’t stay put, or a soft spot at a shower curb or floor drain. You notice it weeks or months after the room was finished, when a tile clicks underfoot or a hairline crack keeps reopening along a Schluter profile edge.
What most Mission Viejo owners run into: the Schluter part itself rarely fails. The failure is almost always assembly-related – membrane bonded to a substrate that moves, a curb built without proper slope, or the wrong trim profile sized for the tile. We install Schluter systems and document every specification so the assembly holds and the manufacturer warranty stays intact.
Key Takeaways
- Home additions in Mission Viejo: $45,000 – $130,000. Full ADUs: $90,000 – $220,000.
- Schluter failures trace back to the assembly, not the part.
- Written price before any work starts – no numbers that move.
- Every project covered by the 365-Day Done Right Promise, in writing.
Which Schluter Models This Applies To

Schluter is a system, not a single part number. When we spec a tile floor or shower, the pieces that matter are the DITRA uncoupling membrane (now DITRA-25 for standard floors), KERDI waterproofing membrane for wet areas, KERDI-BOARD for shower walls and benches, and the SCHIENE, DILEX, and RONDEC edge profiles that finish tile-to-wall and tile-to-floor transitions. Each profile comes in specific widths matched to tile thickness – a 3/8-inch SCHIENE won’t sit flush on a 1/2-inch body tile, and that mismatch is one of the most common “failed part” calls we get.
Identify the right part by measuring tile thickness, then checking the membrane roll width and printed batch markings. For DITRA, you’ll see a printed pattern on the fleece side; OEM rolls carry a legible manufacturer code. Aftermarket clones exist and can meet spec on paper, but Schluter’s own warranty only tracks their branded material. When we install, we use documented Schluter product matched to your tile so the assembly is traceable.
We’re an independent contractor, not affiliated with Schluter – so the spec we give you comes from the manufacturer’s current technical handbook, not a sales sheet.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
Here’s what Mission Viejo owners actually report, and what’s behind it:
- Hollow tile or clicking underfoot. The uncoupling membrane wasn’t fully embedded in thinset – a bonding failure, not a broken membrane.
- Grout cracking along a joint that keeps reopening. The profile was sized wrong for the tile or set without the proper movement joint, so the edge opens with seasonal movement.
- Water at the shower curb or floor drain. KERDI membrane seaming or a missing pre-slope lets moisture sit where it shouldn’t; this shows up as discolored grout or a musty smell.
- Tile lifting at the wall-floor transition. Wrong profile height or fasteners driven too deep into the waterproofing.
- Efflorescence or a soft spot near a floor drain. Water reaching the substrate – in our area, the temperature swings between inland heat and marine cool push movement through the floor assembly, and a weak membrane bond shows first.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed pricing for Schluter-relevant work in Mission Viejo – a real range, not “call for a quote”:
| Scope | Installed range |
|---|---|
| Home addition (Schluter-spec tile & waterproofing) | $45,000 – $130,000 |
| Full ADU construction | $90,000 – $220,000 |
| Walk-in shower installation with KERDI | $4,500 – $12,000 |
| Bathroom remodel (full) | $9,000 – $28,000 |
The range is driven by square footage, tile size and profile count, and how much substrate repair the assembly needs. We give a written price before any work starts – parts, labor, and the waterproofing work itemized so you can see what a Schluter assembly costs versus a bare tile job. The 365-Day Done Right Promise covers the work: if it fails inside that window, we come back and correct it at no charge.
DIY or Call Us?
An owner can safely check tile for hollow spots with a tap, measure tile thickness for profile sizing, and read the printed markings on a membrane. Where DIY goes wrong on Schluter assemblies: embedding a membrane with the wrong thinset, skipping the pre-slope at a drain, or forcing a profile into a joint that needed a movement gap. These aren’t visible for months, and the repair means pulling the tile back up. Nothing here is dangerous to handle – the risk is a failed shower or floor that leaks quietly. Call (833) 734-2429 and we’ll scope it honestly.
FAQs

How long does a Schluter assembly last in Mission Viejo? A correctly installed Schluter waterproofing and uncoupling system typically lasts as long as the tile itself, well over a decade – failures trace to installation, not the material’s lifespan. Call (833) 734-2429 for an exact assessment. Estimates are free.
Can it be repaired instead of replaced? Often yes. If the failure is confined to one area – a single loose tile or a cracked profile joint – we can lift and re-set that section and re-seal the waterproofing rather than rip out the whole floor. We only recommend full replacement when water has reached the substrate. Call (833) 734-2429 for a free look.
How long does the swap take? A profile replacement or a small membrane re-seal is a short job measured in days for that area. A shower rebuild or tile floor replacement runs one to two weeks depending on size and drying time. We put the timeline in the written price before we start.
How do you source the Schluter part? We specify current Schluter product matched to your tile thickness and the assembly shown in the manufacturer’s technical handbook, then order to the documented spec. That keeps the material traceable and the warranty backed. Call (833) 734-2429 to walk through your project with us.
We also install KraftMaid and Cambria, and we’ll coordinate surfaces and cabinetry around your Schluter waterproofing work when a Mission Viejo bathroom or kitchen is on the table.
If you’re planning a home addition or ADU in Mission Viejo and want the tile and waterproofing done right the first time – price in writing, background-checked crew, a full-year guarantee – call Bradford Remodeling Co Mission Viejo at (833) 734-2429 for a free estimate.
Written by the team at Bradford Remodeling Co Mission Viejo, serving Mission Viejo and nearby areas.












